High-Power, Quad, PSE Controller
for Power-Over-Ethernet
24   ______________________________________________________________________________________
Figure 9. Slave Address
SDA
SCL
1
0
A3
A2
A1
A0
0
MSB
LSB
ACK
R/W
Figure 10. Control Byte Received
S
A
A
P
0
SLAVE ADDRESS
CONTROL BYTE
ACKNOWLEDGE FROM MAX5952
ACKNOWLEDGE FROM MAX5952
D15   D14   D13   D12   D11   D10   D9    D8
CONTROL BYTE IS STORED ON RECEIPT OF STOP CONDITION
R/W
Slave Address
The MAX5952 has a 7-bit long slave address (Figure
9). The bit following the 7-bit slave address (bit eight) is
the R/W bit, which is low for a write command and high
for a read command.
010 always represents the first three bits (MSBs) of the
MAX5952 slave address. Slave address bits A3, A2,
A1, and A0 represent the states of the MAX5952s A3,
A2, A1, and A0 inputs, allowing up to sixteen MAX5952
devices to share the bus. The states of the A3, A2, A1
and A0 latch in upon the reset of the MAX5952 into reg-
ister R11h. The MAX5952 monitors the bus continuous-
ly, waiting for a START condition followed by the
MAX5952s slave address. When a MAX5952 recog-
nizes its slave address, the MAX5952 acknowledges
and is then ready for continued communication.
Global Addressing and Alert Response Protocol
The global address call is used in writing mode to write
the same register to multiple devices (address 0x60). In
read mode (address 0x61), the global address call is
used as the alert response address. When responding
to a global call, the MAX5952 puts out on the data line
its own address whenever its interrupt is active. So
does every other device connected to the SDAOUT line
that has an active interrupt. After every bit transmitted,
the MAX5952 checks that the data line effectively cor-
responds to the data it is delivering. If it is not, it then
backs off and frees the data line. This litigation protocol
always allows the part with the lowest address to com-
plete the transmission. The microcontroller can then
respond to the interrupt and take proper actions. The
MAX5952 does not reset its own interrupt at the end of
the alert response protocol. The microcontroller has to
do it by clearing the event register through their CoR
adresses or activating the CLR_INT pushbutton.
Message Format for Writing to the MAX5952
A write to the MAX5952 comprises of the MAX5952s
slave address transmission with the R/W bit set to 0, fol-
lowed by at least one byte of information. The first byte
of information is the command byte (Figure 10). The
command byte determines which register of the
MAX5952 is written to by the next byte, if received. If
the MAX5952 detects a STOP condition after receiving
the command byte, the MAX5952 takes no further
action beyond storing the command byte. Any bytes
received after the command byte are data bytes. The
first data byte goes into the internal register of the
MAX5952 selected by the command byte. If the
MAX5952 transmits multiple data bytes before the
MAX5952 detects a STOP condition, these bytes store
in subsequent MAX5952 internal registers because the
control byte address auto-increments.
相关PDF资料
MAX5953DUTM+ IC INTERFACE 802.3AF 48TQFN
MAX5954LETX+T IC PCI EXP/HOT-PLUG CTRLR 36TQFN
MAX5955BEEE+ IC DUAL HOT-SWAP CTRLR 16-QSOP
MAX5957AETN+T IC TRPL PCI EXP/HOT-PLUG 56-TQFN
MAX5960AECS+T IC CTRLR HOT-PLUG QD 80-TQFP
MAX5963UTL+T IC HOT SWAP DIO ORING CTL 40TQFN
MAX5965AEAX+ IC PSE CTRLR FOR POE 36SSOP
MAX5969DETE+T IC CTRLR INTERFCE W/MOSFT 16TQFN
相关代理商/技术参数
MAX5952CUAX+T 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5952DEAX+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX5952DEAX+T 制造商:Maxim Integrated Products 功能描述:HIGH-POWER QUAD PSE CONTROLLER FOR - Tape and Reel
MAX5952DUAX+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX5952DUAX+T 制造商:Maxim Integrated Products 功能描述:HIGH-POWER QUAD PSE CONTROLLER FOR - Tape and Reel
MAX5953AUTM+ 功能描述:电压模式 PWM 控制器 IEEE 802.3af PD Int & PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
MAX5953AUTM+T 功能描述:电压模式 PWM 控制器 IEEE 802.3af PD Int & PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
MAX5953BUTM+ 功能描述:电压模式 PWM 控制器 IEEE 802.3af PD Int & PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel